TM 5-3825-213-20
Service
Service
Inspe
Quar
Inspe
Quar
ction
terly
ction
terly
25 Charge or replace batteries; clean or replace
10).
Replace defective or damaged
battery cables and connectors. Protect
throttle (par. 133), choke (par. 134),clutch
connectors from corrosion by coating
linkage (par. 86), and hydraulic control
lightly with cup grease (par. 250).
26 Alternator, starters. Inspect the alternator,
Frame. Inspect the carrier frame and plow
32
32
26
starter motor, starter motor solenoid
frame for damage or misalinement.
relay, and electrical connections of each
32
Report any frame damage or misalinement
engine for condition, loose mounting,
to field maintenance, 3rd echelon.
Hood, panels, doors. Inspect the engine
and improper operation.
33
33
26 Tighten loose mountings and connections.
hoods and carrier cab doors for damage
Replace defective alternator (par. 101),
or misalinement. Inspect the fenders for
starter motor (par. 91), or starter
damage.
solenoid relay (par. 92).
Replace
33
Replace or repair hoods (pars. 193 and
defective starter motor brushes (par.
195), doors (pars. 248 and 249). seats
(par. 247), and fenders (par. 257).
27 Distributors. Inspect the wiring of engine
Plow engine clutch. Inspect the plow engine
27
34
34
distributor for improper connection or
clutch for proper adjustment.
damage. Inspect the distributors for
34
Adjust the clutch if necessary. Report any
damage to cap, points, and capacitor.
unsatisfactory operation, which cannot be
Measure point gap. The proper gap is
corrected by adjustment to field
0.020-0.022 inch.
maintenance, 3d echelon.
Gages. Inspect all nonelectrical gages for
27 Tighten or replace wiring (par. 93). Adjust the
35
35
distributor points (par. 95).
Report
satisfactory operation.
damaged or defective distributor to field
35
Replace damaged or defective gages (pars.
maintenance, 3d echelon.
28 Coil, wiring, switches. Inspect condition and
28
Meters. Inspect all electrical gages, the
36
36
appearance of the engine ignition
tachometer, and the speedometer for
systems.
Inspect for loose wire
satisfactory operation.
connections, broken wire, and broken
36
Replace damaged or defective electrical
connecting terminal posts.
gages (pars. 128, 132, 142, 149, and
28 Repair damaged wiring (par. 93).
153). Replace defective tachometer or
29 Alternator regulator. Inspect the alternator
29
speedometer (pars. 127 and 137).
Steering gear assembly.
regulator for loose mounting, defective
Inspect the
37
37
terminal connections, and unsatisfactory
steering gearbox lubricant level. Inspect
operation.
steering play by moving steering wheel.
29 Replace defective alternator regulators (par.
37
Adjust steering gear (par. 259). Lubricate if
and
tighten
loose
wiring
necessary (LO 5-3825-213-20).
connections.
Safety valve. Inspect the safety valve for
38
38
30 Lights, wiring.
Inspect all lights, their
30
proper operation and secure mounting
mountings, switches, and wiring for
damage and improper operation.
38
Replace defective safety valve (fig. 129).
30 Replace defective lamps, switches, and
Hydraulic pump, air compressor. Inspect the
39
39
plow and steering hydraulic pump for
31 Levers, pedals, linkage, cables. Inspect the
31
leaks and unsatisfactory operation.
plow engine clutch, engine starters,
Inspect the air compressor for lubricant
throttles,
chokes,
accelerator,
level, air or lubricant leaks and
transmission shift lever, plow hydraulic
unsatisfactory operation.
control levers, handbrake, and power
39
Replace defective hydraulic steering pump
transfer shifter linkages for condition and
(par. 235) and plow hydraulic pump (par.
adjustment.
58). Report defective air compressor to
31 Adjust plow engine clutch (TM 5-3825-213-
field maintenance, 3d echelon.
23