TM 5-3825-213-35
1
Nut, 1 in. -14
8
Nut, 1 -12
2
Fitting, lubrication
9
Washer, lock, 1 in.
3
Nut, 1 in. -14
10
Nut, -13 (3 rqr)
4
Washer, lock, 1 in.
11
Washer, lock, in. (8 rqr)
5
Adjusting bracket
12
Screw, machine, countersunk flat head, -13 x 1
6
Nut, 1 in. -14- in.
(2 rqr)
7
Fitting, lubrication
13 Snowplow frame
A. Snowplow frame.
1
Adjuster stud
3 Seal plate
2
Sprocket
4 Sleeve bushing
B. Adjusting sprocket.
1
Lower idler sprocket stud
3 Spacer
2
Lower idler sprocket
4 Sleeve bushing
C. Lower idler sprocket.
1
Nut, -13 (2 rqr)
6 Screw, machine, countersunk flat head, -13 x 1
2
Washer, lock, in. (2 rqr)
in.
3
Bracket
7 Bracket w/stud
4
Spacer
8 Fitting
5
Upper idler sprocket
P. Upper idler sprocket.
1 Nut, 3/8-24 (3 rqr)
9 Bearing
2 Washer, lock, 3/8 in. (3 rqr)
10 Screw, -20 x in. (4 rqr)
3 Nut, -13 (4 rqr)
11 Retainer
4 Washer, lock, in. (4 rqr)
12 Washer, special
5 Housing
13 Bearing
6 Screw, 3/8-16 x 1 in. (4 rqr)
14 Bearing
7 Washer, lock, 3/8 in. (4 rqr)
15 Lubrication fitting
8 Cover
16 Sleeve
E. Auger drive chain sleeve.
1 Screw, machine, countersunk flat head, -13 x
3 Key
1 in. (4 rqr)
4 Drive sprocket
2 Setscrew, special
F. Drive sprocket.
Figure 48. Continued.
(3) Install the sprocket assemblies and
178.
Snowplow
Frame
Assembly
Cleaning,
drive chain (par. 175).
Inspection and Repair
(4) Install the fan and auger gearcase
Cleaning. Clean all parts in an approved
a.
assembly (par. 167), and fan housing
cleaning solvent and dry thoroughly.
Inspection and Repair. Inspect all parts for
b.
(5) Install the auger drive shaft (par. 163).
wear, breaks, and damaged bearings and shafts. Repair
(6) Install the shoes and skates (TM 5-
or replace defective parts and repair all broken welds.
3825-213-20).
(7) Install the cutting edge and side cutters
179.
Snowplow Frame Assembly Reassembly and
(TM 5-3825-213-20).
Installation
(8) Install the fan housing rotating cylinder
(TM 5-3825-213-20).
a.
Reassembly.
(9) Install the chute trough assembly (TM 5-
(1) Reassemble the snowplow frame
3825-213-20).
assembly in reverse of numerical
sequence illustrated on figure 48.
Installation.
Install the snowplow frame
b.
assembly (TM 5-3825-213-10).
(2) Install the augers (TM 5-3825-213-20).
120