TM 5-3825-213-35
31 Adjusting nut, special
1
Nut, No. 1032
32 Spring
2
Washer, lock, No. 10
33 Screw, adjusting, special
3
Washer, flat, No. 10
34 Screw, machine, No. 10-32x 1/4 in. (2 rqr)
4
Insulating washer
35 Washer, lock, No. 10 (2 rqr)
5
Screw, machine, No. 10-32 x
2 1/4 in.
36 Washer, flat, No. 10 (2 rqr)
6
Relay electrical lead
37 Armature
7
Fixed resistor
38 Nut, 1/420
8
Nut, No. 1032
39 Washer, lock, 1/4 in.
9
Washer, lock, No. 10
40 Nut, 1/420
10
Washer-, flat, No. 10
41 Washer, lock, 1/4 in.
11
Screw, machine, No. 10-32 x
1/2 in. (2 rqr)
42 Washer, flat, 1/4 in.
12
Resistor assembly
43 Insulating washer
13
Nut, No. 10-32
44 Insulating bushing
14
Washer, lock, No. 10
45 Contact plate
15
Nut, No. 10-32
46 Contact insulator plate
16
Washer, lock, No. 10
47 Armature stop
17
Washer, flat, No. 10
48 Nut, No. 10-32
18
Screw, machine, No. 10-32 x
3/4 in.
49 Washer, lock, No. 10
19
Nut, No. 4-40
50 Nut, No. 10-32
20
Washer, lock
51 Washer, lock, No. 10
21
Screw, machine, No. 10-32 x
3/4 in.
52 Washer, flat, No. 10
22
Washer, lock, No. 10
53 Screw, No. 1032 x 3/4 in.
23
Washer, flat, No. 10
54 Fixed resistor (360-ohm)
24
Clip
55 Nut, No. 440
25
Sleeve
56 Washer, lock, ET, No. 4
26
Clip
57 Washer, flat, No. 14
27
Screw, No. 10-32 x 5/16 in.
58 Screw, No. 4-40 x 3/4 in.
28
Washer, lock, 5/16 in.
59 Rectifier lead
29
Washer, flat, 5/16 in.
60 Panel
30
Operating coil assembly
Figure 3-Continued.
Section IV. REMOVAL AND INSTALLATION OF MAJOR COMPONENTS OR AUXILIARIES
(2) Close shutoff valve on fuel tanks and
47. General
remove the fuel line (TM 5 3825-213-20).
The major components and auxiliaries of the snow
(3) Drain the coolant system (TM 5 3825-213-
removal unit consist of the plow engine, carrier engine,
10).
transfer
case,
torqmatic
transmission,
plow
(4) Drain the lubricating system (TM 54825-
transmission, and plow assembly.
213-10).
(5) Remove the battery cables and wiring
48. Plow Assembly
(TM 5-3825-213-20).
(6) Remove the necessary oil, heater, and
a. Removal. Remove the plow assembly (TM 5-
coolant lines (TM 54825-213-20).
3825-213-10).
(7) Remove the oil pan shields (TM 5-3825-
b. Installation. Install the #low assembly (TM 5-
213-20).
3825-213-10).
(8) Remove the plow transmission (par. 53).
(9) Remove the plow engine and clutch ,
49. Plow Engine and Clutch Assembly
assembly as instructed on figure 4.
b. Installation.
a. Removal.
(1) Install the plow engine and clutch
(1) Remove the plow engine hood (TM 5-
assembly as instructed on figure 4.
3825-213-20).
(2) Install the plow transmission (par. 53).
36