TM 5-3825-213-35
1
Screw, machine, No. 6-32 x 1/2 in.
4
Screw, machine, No. 6-32 x 1/2 in.
2
Washer, fiber, No. 6
6
Washer, fiber, No. 6
3
Venturi tube
6
Venturi tube
G. Carburetor venturi tube.
1
Connector tube
16 Nut, lock, No. 8-32
2
Connector tube washer
17 Diaphragm rod
3
Passage plug
18 Spring
4
Passage plug washer
19 Seal and wire
5
Setscrew, No. 6-32 x 1/8 in.
20 Screw, machine, 6-32 x 3/8 in. (3 rqr)
6
Seal and wire
21 Washer, lock, No. 6 (3 rqr)
7
Screw, machine, No. 8-32 x 1/2 in. (3 rqr)
22 Housing cover plate
8
Washer, lock, No. 8 (3 rqr)
23 Gasket
9
Screw, machine, special (5 rqr)
24 Screw, machine, slave unit to throttle body (4
10
Washer, lock, No. 8 (5 rqr)
rqr)
11
Switch cover and valve
25 Screw, machine, No. 5-40 x 3/16 in.
12
Diaphragm washer
26 Washer, lock, No. 5
13
Diaphragm
27 Throttle lever
14
Diaphragm washer
28 Gasket
15
Housing rod connector
29 Slave unit housing
H. Slave unit assembly.
1
Gasket
14 Throttle shaft thrust washer
2
Throttle plate screw (4 rqr)
15 Throttle control shaft
3
Throttle plate (2 rqr)
16 Driver assembly screw
4
Screw, fillister head, No. 10-32 x 3/4 in.
17 Driver screw washer
5
Throttle clamp lever
18 Throttle shaft driver
6
Stop pin screw
19 Drive shaft flat washer
7
Washer, lock stop pin screw
20 Idle adjusting needle
8
Throttle stop mounting screw
21 Adjusting needle spring
9
Washer, lock, No. 10
22 Seal retaining washer (2 rqr)
10
Throttle lever and stop
23 Adjusting needle seal
11
Gasket
24 Needle shaft bearing
12
Screw, machine, No. 10-32 (2 rqr)
25 Bearing seal washer
13
Stop screw spring (2 rqr)
26 Throttle body
I. Throttle body.
Figure 56 - Continued.
207. Plow and Carrier Engine Carburetor Assemblies
208. Plow and Carrier Engine Carburetor Assemblies
Cleaning, Inspection, and Repair
Reassembly and Installation
a. Cleaning. Clean all parts with an approved
Reassemble the carburetor in
a. Reassembly.
cleaning solvent and dry thoroughly.
reverse of numerical sequence illustrated on figure 56.
b. Inspection and Repair. Inspect all parts for
b. Installation. Install the carburetor (TM 5-3825-
defective condition. Replace or repair all worn, defective,
213-20).
or damaged parts.
Section VIII. PLOW AND CARRIER ENGINE RADIATOR ASSEMBLIES
by this type of flushing, the radiator must be removed and
209. General
cleaned as instructed in this section. The carrier engine
On-equipment flushing instructions are given in TM 5-
radiator consists of top and bottom tanks and a tube-type
3825-213-20. If a clogged condition cannot be corrected
144
