h. Depot Maintenance Allowance Per 100
indicates the Federal stock number includes all
armament, equipment, accessories, and repair parts
Equipments. This column indicates opposite the first
issued with the item. A part number or other reference
appearance of each item the total quantity authorized
number is followed by the applicable five-digit Federal
for depot maintenance of 100 equipments. Subsequent
supply code for manufacturers in parenthesis. Repair
appearances of the same item will have the letters
parts quantities included in kits and sets are shown in
"REF" in the allowance column.
To locate the
front of the repair part name. Material required for
referenced item, locate the FSN or reference number in
manufacture of fabrication is identified.
the index. The earliest figure and item number is the
referenced item. Items authorized for use as required
d. Unit of Measure (U/M). A 2 character alphabetic
but not for initial stockage are identified with an asterisk
abbreviation indicating the amount or quantity of the
in the allowance column.
item upon which the allowances are based, e.g., ft, ea,
pr, etc.
i. Illustration. This column is divided as follows:
e. Quantity Incorporated in Unit. This column
(1) Figure number.
Indicates the figure
indicates the quantity of the item used in the assembly
number of the illustration in which the item is shown.
group. A "V" appearing in this column in lieu of a
(2) Item number.
Indicates the callout
quantity indicates that a definite quantity cannot be
number used to reference the item in the illustration.
indicated (e.g., shims, spacers, etc.).
4. Special Information
f. Thirty-Day DS/GS Maintenance Allowances.
a. Identification of the usable on codes included in
Note
the description column of this publication are:
Allowances in GS column are for GS
maintenance only.
Code
Used on
A
Applies to parts associated with and used
on
(1) The allowance columns are divided into
Waukesha Engine Model T11884 as used on
the
three subcolumns.
Indicated in each subcolumn,
snow plow.
opposite the first appearance of each item, is the total
B-
Applies to parts associated with and used
on
quantity of items authorized for the number of
Waukesha Engine Model THS884 as used on
the
equipments supported. Subsequent appearances of the
carrier.
same item will have the letters REF in the applicable
allowance column. To locate the referenced item,
Repair parts not symbolized are applicable to the end
locate the FSN or reference number in the index. The
item.
earliest figure and item number is the referenced item.
b. Repair parts mortality has been based on 800
Items authorized for use as required but not for initial
hours operation per year.
stockage are identified with an asterisk in the allowance
c. Parts which require manufacture or assembly at
column.
a category higher than that authorized for installation will
(2) The quantitative allowances for DS/GS
indicate in the source column the higher category.
levels of maintenance will represent initial stockage for
d. Action change codes indicated in the left hand
a 30-day period for the number of equipments
margin of the listing page denote the following:
supported.
N - Indicates an added item not included in previous
(3) To determine allowances when supporting
publications.
more than 100 of these equipments: First, divide the
C - Indicates a change in data.
number of equipments supported by 100 by moving the
F - Indicates a change in FSN only.
decimal two places left; second, multiply the result by
e. The following publications pertain to the snow
the quantity in the 51-100 density column. Example,
removal unit and its components.
authorized allowance for 51-100 equipments is 40; for
TM 5-3825-213-10
Operators manual.
150 equipments multiply 40 by 1.50 or 60 parts required.
TM 5-3825-213-20
Organizational main-
g. One-Year Allowance Per 100 Equipments/
tenance manual.
Contingency Planning Purposes. This column indicates
TM 5-3825-213-20P
Organizational main-
opposite the first appearance of each item the total
tenance repair parts
quantity required for distribution and contingency
and special tool lists.
planning purposes. The range of items indicates total
TM 5-3825-213-35
Field and depot main-
quantities of all authorized items required to provide for
tenance manual.
adequate support of 100 equipments for one year.
LO 5-3825-213-20-1-2-3
Lubrication order.
Subsequent appearances of the same item will have the
5. How to Locate Repair Parts
letters "REF" in the allowance column. To locate the
a. When Federal stock number or reference
referenced item, locate the FSN or reference number in
number is unknown:
the index. The earliest figure and item is the referenced
item.
vi
